What is it, how do you do it, where can I get it or where can I learn how to do it? Tatting itself is a relatively new art form that is currently enjoying a genuine resurgence in popularity. You will immediately have a whole host of new friends all wanting to know exactly what you are doing. To confirm that just sit down in the presence of any large group, pull out your tatting shuttle and start putting rings and picots together. Then you can move on to Lesson 2: Chains, Rings, Picots, and Joins.The allure of tatting is undeniable. If you didn’t get it the first time, keep trying until you do! You can do it! Once you get it, keep practicing it until you’re fairly comfortable with it. It seems to be one of those things that is confusing at first, until the “light goes on”, so to speak. This is the hardest part of tatting, and can be very frustrating to learn. If not, you probably didn’t get the thread to “flip”. When you are done, you should be able to slide the knot along the shuttle thread. Then repeat the motions as for the first half of the double stitch to tighten the knot. Pass the shuttle under the working thread, letting the thread slip between the shuttle and your fingers. This time, without rolling your hand, pass the shuttle over the working thread, letting the thread slip between the shuttle and your thumb. Once it’s snug on the shuttle thread, grab onto it with the thumb and middle finger. The knot will move toward your thumb and middle finger and tighten. Keep the shuttle thread taut while you raise the finger on the left hand to pull the working thread taut. When you do this, the loop in the thread will “flip” from the shuttle thread to the working thread. Relax your first finger of your left hand enough to let the working thread go slack. Then pass the shuttle over the working thread, letting the thread slip between the shuttle and your thumb. Pull the working thread taught by raising your index finger on your left hand. Roll your right hand toward you so that the thread exits on the side of your hand away from you, then passes over your hand. Grasp the shuttle so that the point of it points toward the tip of your fingers and the thread exits the shuttle toward your pinkie. Wrap it around your pinkie finger until it’s secure enough that you can get some tension in the thread. Pass the working thread over your left hand, starting over your index finger and going to your pinkie finger. The “working thread” is the thread coming from your thumb over your hand.Ĭross the shuttle thread and the working thread perpendicular to each other and grip it between your thumb and your middle finger. If you’re left-handed, it will be your right hand.) The “shuttle thread” is the thread coming from the shuttle to your left hand (If you’re right-handed. You can do it either way and still learn from these instructions. I crocheted before I tatted, and I found this grip more comfortable than the usual tatting grip. This is a little unconventional because I grasp the thread with my middle finger instead of with my first finger. I will describe here how I hold my tatting thread. Fortunately, there are shuttle winders available that make quick work of it. Winding shuttles can be tedious and time-consuming. Don’t over-fill the shuttle since this can spread the points. Hold the shuttle so you can see the post, and wind the thread onto it until it’s full. Thread the thread through the hole in the shuttle’s post and tie a knot. You can use two different colors of thread if you can’t find variegated thread.Īny tatting shuttle will do, but my favorites are Clover shuttles and Aerlit shuttles because they fit so neatly into your hand and they’re easy to grasp. The thread makes bigger and more visible stitches, and the differences in color make the stitches show up even further. A size 10 variegated thread, if you can find it, is good to use. You can learn to shuttle tat, too, but I suggest you don’t use buttonhole thread to do it. So much so, that I didn’t go shopping for a good thread to learn with, I pulled out some buttonhole thread and just sat down to do it. I was determined and stubborn, and I wanted to learn immediately.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |